Search found 462 matches

by mikemoy
Sun Jun 17, 2018 7:15 am
Forum: General Discussion
Topic: Hardware Pin Assignment
Replies: 2
Views: 1419

Re: Hardware Pin Assignment

Are you using the Wrover or the Wroom ?
Do you plan on using JTAG ?

I dont use JTAG, and am using 12,13,14,15 for SPI. 4&5 for I2C, & GPIO2 for controlling a relay with no issues.
by mikemoy
Sun Jun 10, 2018 2:18 pm
Forum: General Discussion
Topic: Flashing ESP-Wroom-32 in production
Replies: 12
Views: 6489

Re: Flashing ESP-Wroom-32 in production

You pin selection for serial programming is correct. Should you need an off the shelf programmer you could use one of these. http://www.electrodragon.com/product/esp-prog-board-for-esp8266-esp32/ Or should you choose to program the modules before they are placed in your board, you can program them w...
by mikemoy
Sat Jun 09, 2018 4:57 pm
Forum: General Discussion
Topic: ESP32 Pocket Programmer ?
Replies: 2
Views: 970

Re: ESP32 Pocket Programmer ?

I have a couple of those, and yes that is actually a great idea. No need to re-invent the wheel.
by mikemoy
Sat Jun 09, 2018 3:49 pm
Forum: General Discussion
Topic: Flashing ESP-Wroom-32 in production
Replies: 12
Views: 6489

Re: Flashing ESP-Wroom-32 in production

I was referring til JTag, which by "google" it seems to be possible, but not recommended.
Glad you have it figured out, but I wanted to clarify this for others that may see this post.
There is nothing wrong at all programming it with JTAG.
by mikemoy
Sat Jun 09, 2018 2:09 pm
Forum: General Discussion
Topic: ESP32 Pocket Programmer ?
Replies: 2
Views: 970

ESP32 Pocket Programmer ?

Just trying to get a vibe on if creating a ESP32 Pocket Programmer would be a good venture or not. We have used these for many years on the production floor, and for infield updates for Atmel products. http://npe-inc.com/pocket-programmer/ Basically you upload your firmware to the programmer, connec...
by mikemoy
Sat Jun 09, 2018 1:37 pm
Forum: General Discussion
Topic: Flashing ESP-Wroom-32 in production
Replies: 12
Views: 6489

Re: Flashing ESP-Wroom-32 in production

but I have now read several places that this is not supported/recommended with ESP32.
Where did you see that ?

How about the ESP32 Programming Tool ?
by mikemoy
Sun Jun 03, 2018 6:06 am
Forum: General Discussion
Topic: Unable to connect to EPS32
Replies: 5
Views: 1690

Re: Unable to connect to EPS32

If what Kolban says does not work, and your sure you have the right com port. Try sticking a 0.1uf -0.22uf from pin 3 (EN) to gnd.
by mikemoy
Sat Jun 02, 2018 11:05 pm
Forum: General Discussion
Topic: Red light is always on
Replies: 8
Views: 8276

Re: Red light is always on

Try sticking a 0.1uf -0.22uf from pin 3 (EN) to gnd.
by mikemoy
Fri Jun 01, 2018 11:59 pm
Forum: General Discussion
Topic: use of LED control for buzzer?
Replies: 12
Views: 4296

Re: use of LED control for buzzer?

That was measured with a scope with 4kHz signal. There's no negative voltage if I drop the GPIO drive strength to minimum. I would not expect a piezo transducer to work well if it's just in series with the drain of a transistor but that should be OK for the electro-magnetic transducer. Cool, at lea...
by mikemoy
Fri Jun 01, 2018 10:04 pm
Forum: General Discussion
Topic: use of LED control for buzzer?
Replies: 12
Views: 4296

Re: use of LED control for buzzer?

Just an FYI, it's not a good idea to drive a piezo electric device via a GPIO pin. Piezo devices can generate negative voltages. I'm getting only -40mV. Is that measured with a scope or meter. You will get much higher voltages than this when you turn a piezo off at the right time. Similar to say wh...

Go to advanced search