Search found 194 matches

by username
Wed May 13, 2020 12:06 pm
Forum: General Discussion
Topic: ESP32: Use Arduino or ESP-IDF?
Replies: 16
Views: 21245

Re: ESP32: Use Arduino or ESP-IDF?

You can leave it the way you posted it, its just fine. I will mention this though. concerning blink.c. You might want to consider moving these to into main.c, before you do anything else. I would also add after these, gpio_set_level(BLINK_GPIO, 0); with either a 0 or a one to set the pin state to wh...
by username
Tue May 12, 2020 2:25 am
Forum: General Discussion
Topic: ESP32: Use Arduino or ESP-IDF?
Replies: 16
Views: 21245

Re: ESP32: Use Arduino or ESP-IDF?

You dont get all the extra flexibility from menuconfig to do enhancements and fine tuning.
by username
Mon May 11, 2020 3:38 pm
Forum: General Discussion
Topic: Can someone explain my oscillating touch readings?
Replies: 3
Views: 599

Re: Can someone explain my oscillating touch readings?

It radiated energy from everything around you. Lights, power supplies and so on. You body is an antenna that picks up this noise.
You can think of it if you ever dealt with audio amplifiers and touched the input cable while it was plugged in and head that typical "hum" noise.
by username
Sun May 10, 2020 12:11 pm
Forum: ESP IoT Solution
Topic: Esp Now distance.
Replies: 1
Views: 1000

Re: Esp Now distance.

I don't know if there is another solution in software to help. I do remember seeing a way to change the output power. But I don't know if by default its set to the highest level. I would also look into using the ESP32 module with the U.FL (IPEX) CONNECTOR on it. https://www.gridconnect.com/products/...
by username
Tue May 05, 2020 1:32 am
Forum: Hardware
Topic: Upload code without pressing EN and Boot buttons
Replies: 12
Views: 1909

Re: Upload code without pressing EN and Boot buttons

I never used a ESP8266. Just head over to espressif web site and download the schematic for it to see.
by username
Mon May 04, 2020 1:06 pm
Forum: Hardware
Topic: Upload code without pressing EN and Boot buttons
Replies: 12
Views: 1909

Re: Upload code without pressing EN and Boot buttons

OK, great you have one. You do not need to press the buttons to get it into flash mode. If you do there is something wrong. There are many knock-offs out there that there is a issue with the timing on the GPIO0 signal which forces you do press the buttons. The real legitimate boards that are not che...
by username
Mon May 04, 2020 12:46 pm
Forum: Hardware
Topic: Upload code without pressing EN and Boot buttons
Replies: 12
Views: 1909

Re: Upload code without pressing EN and Boot buttons

Absolutely it will work. Don't you have one of those kits? Or any of the others ones like it? IF not buy one and you will see for yourself.

You do not need to push those buttons to set it up for flash mode.
by username
Mon May 04, 2020 12:27 pm
Forum: Hardware
Topic: Upload code without pressing EN and Boot buttons
Replies: 12
Views: 1909

Re: Upload code without pressing EN and Boot buttons

They have the buttons, but you do not need to use them. The circuit on the board takes care of the EN and GPIO line toggling when you go to flash it.
by username
Mon May 04, 2020 12:14 pm
Forum: Hardware
Topic: Upload code without pressing EN and Boot buttons
Replies: 12
Views: 1909

Re: Upload code without pressing EN and Boot buttons

Oh... Then just put the same circuit on the board as the ESP32 DevKitC. Look at the schematic on this page.

https://docs.espressif.com/projects/esp ... -documents
by username
Mon May 04, 2020 12:09 pm
Forum: ESP32 Arduino
Topic: ESP32 Scheduling
Replies: 3
Views: 827

Re: ESP32 Scheduling

What is the problem? If your getting the time, and you have the time lapse working.

Go to advanced search