ESP BLE Mesh v0.5 Beta版本烧入到板子里,串口打印乱码

chenluhui2019
Posts: 33
Joined: Wed Apr 10, 2019 9:08 am

ESP BLE Mesh v0.5 Beta版本烧入到板子里,串口打印乱码

Postby chenluhui2019 » Wed Apr 10, 2019 9:18 am

在下载了ble_mesh相关代码后,编译esp-idf\examples\bluetooth下的ble_mesh代码,烧写到板子里。串口打印的是乱码,如下:
各位有遇到这个现象吗?
ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0018,len:4
load:0x3fff001c,len:5984
ho 0 tail 12 room 4
load:0x40078000,len:9308
load:0x40080400,len:6148
entry 0x40080748
s0ce$``g™8e 8!a,Fa'e!5y
)5+={ F!*>,{%#(y)5{%#!={({%#%!!y
DB8)e
(,1@,+%+0h5aIEh”X)ca{-+-E%2+(`~̪ ~+2_P=+S

Wangcheng
Posts: 73
Joined: Wed Mar 06, 2019 3:26 am

Re: ESP BLE Mesh v0.5 Beta版本烧入到板子里,串口打印乱码

Postby Wangcheng » Thu Apr 11, 2019 2:25 am

chenluhui2019 wrote:
Wed Apr 10, 2019 9:18 am
在下载了ble_mesh相关代码后,编译esp-idf\examples\bluetooth下的ble_mesh代码,烧写到板子里。串口打印的是乱码,如下:
各位有遇到这个现象吗?
ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0018,len:4
load:0x3fff001c,len:5984
ho 0 tail 12 room 4
load:0x40078000,len:9308
load:0x40080400,len:6148
entry 0x40080748
s0ce$``g™8e 8!a,Fa'e!5y
)5+={ F!*>,{%#(y)5{%#!={({%#%!!y
DB8)e
(,1@,+%+0h5aIEh”X)ca{-+-E%2+(`~̪ ~+2_P=+S
请问你是使用的什么开发板?你可以先尝试更改一下串口终端的波特率,波特率要和烧写时的波特率一致。

Wangcheng
Posts: 73
Joined: Wed Mar 06, 2019 3:26 am

Re: ESP BLE Mesh v0.5 Beta版本烧入到板子里,串口打印乱码

Postby Wangcheng » Thu Apr 11, 2019 2:31 am

Wangcheng wrote:
Thu Apr 11, 2019 2:25 am
chenluhui2019 wrote:
Wed Apr 10, 2019 9:18 am
在下载了ble_mesh相关代码后,编译esp-idf\examples\bluetooth下的ble_mesh代码,烧写到板子里。串口打印的是乱码,如下:
各位有遇到这个现象吗?
ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0018,len:4
load:0x3fff001c,len:5984
ho 0 tail 12 room 4
load:0x40078000,len:9308
load:0x40080400,len:6148
entry 0x40080748
s0ce$``g™8e 8!a,Fa'e!5y
)5+={ F!*>,{%#(y)5{%#!={({%#%!!y
DB8)e
(,1@,+%+0h5aIEh”X)ca{-+-E%2+(`~̪ ~+2_P=+S
请问你是使用的什么开发板?编译之前你先 make defconfig 一下。你也可以先尝试更改一下串口终端的波特率,波特率要和烧写时的波特率一致。

Who is online

Users browsing this forum: No registered users and 5 guests