ESP32 Forum

Code: Untitled.c Select all

/* Blink Example



   This example code is in the Public Domain (or CC0 licensed, at your option.)



   Unless required by applicable law or agreed to in writing, this

   software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR

   CONDITIONS OF ANY KIND, either express or implied.

*/

#include "freertos/FreeRTOS.h"

#include <stdio.h>

#include "driver/gpio.h"

#include "sdkconfig.h"

#include "driver/spi_common.h"

#include "driver/spi_master.h"

#include "freertos/task.h"









#include "EPD_Test.h"

#include "EPD_4in2.h"



/* Can use project configuration menu (idf.py menuconfig) to choose the GPIO to blink,

   or you can edit the following line and set a number here.

*/

#define BLINK_GPIO 16//0 is turn on,1 is turn off

//the list pins are controled by spi

//#define PIN_NUM_MISO 37

#define PIN_NUM_MOSI 13

#define PIN_NUM_CLK  14



#define PIN_NUM_CS   15

#define PIN_NUM_RST 2

#define PIN_NUM_BUSY 4

#define PIN_NUM_DC 12





esp_err_t ret;

spi_device_handle_t spi;

spi_transaction_t t;



void gpio_init(void){

    /* Configure the IOMUX register for pad BLINK_GPIO (some pads are

       muxed to GPIO on reset already, but some default to other

       functions and need to be switched to GPIO. Consult the

       Technical Reference for a list of pads and their default

       functions.)

    */

    gpio_pad_select_gpio(BLINK_GPIO);

    /* Set the GPIO as a push/pull output */

    gpio_set_direction(BLINK_GPIO, GPIO_MODE_OUTPUT);

    /*e-paper rest pin ,mode is output*/

    gpio_pad_select_gpio(PIN_NUM_RST);

    gpio_set_direction(PIN_NUM_RST, GPIO_MODE_OUTPUT);

    /*e-paper data or command pin ,mode is output*/

    gpio_pad_select_gpio(PIN_NUM_DC);

    gpio_set_direction(PIN_NUM_DC, GPIO_MODE_OUTPUT);

    /*e-paper busy pin ,mode is input*/

    gpio_pad_select_gpio(PIN_NUM_BUSY);

    gpio_set_direction(PIN_NUM_BUSY, GPIO_MODE_INPUT);   

}



void spi_init(void){



    spi_bus_config_t my_config={

        .miso_io_num=-1,

        .mosi_io_num=PIN_NUM_MOSI,

        .sclk_io_num=PIN_NUM_CLK,

        .quadwp_io_num=-1,

        .quadhd_io_num=-1,

        .max_transfer_sz=1000,

    };

    

    spi_device_interface_config_t my_device={

        .flags=SPI_DEVICE_NO_DUMMY,

        .input_delay_ns=10,

        .command_bits=0,

        .address_bits=0,

        .clock_speed_hz=10*1000*1000,

        .mode=0,

        .spics_io_num=-1,

        .queue_size=7,

    };





    ret=spi_bus_initialize(HSPI_HOST, &my_config, 0);

    ESP_ERROR_CHECK(ret);



    ret=spi_bus_add_device(HSPI_HOST, &my_device, &spi);

    ESP_ERROR_CHECK(ret);

    





}



void app_main(void)

{

    gpio_init();

    spi_init();

    printf("SPI gpio Init success!");

    //DEV_Module_Init();

    //EPD_4IN2_Init();

    printf("EPD Init success!");

    //EPD_4IN2_Clear();

    EPD_4in2_test();

    while(1) {

        /* Blink off (output low) */

	printf("Turning off the LED\n");

        gpio_set_level(BLINK_GPIO, 0);

        vTaskDelay(1000 / portTICK_PERIOD_MS);

        /* Blink on (output high) */

	printf("Turning on the LED\n");

        gpio_set_level(BLINK_GPIO, 1);

        vTaskDelay(9000 / portTICK_PERIOD_MS);

    }

}

Code: Untitled.c Select all

#include "DEV_Config.h"

#include <string.h>



extern esp_err_t ret;

extern spi_device_handle_t spi;



extern spi_transaction_t t;

//SPI_TRANS_USE_RXDATA





void DEV_SPI_WriteByte(UBYTE value)

{

    //memset(&t,0,sizeof(t));

    t.flags=SPI_TRANS_USE_TXDATA;

    t.length=8;

    t.tx_data[0]=value;

    t.rx_buffer=NULL;

    //HAL_SPI_Transmit(&hspi1, &value, 1, 1000);

    //spi_device_transmit(spi,&t);

    spi_device_polling_transmit(spi,&t);

    assert(ret==ESP_OK);            //Should have had no issues.



}



void DEV_Module_Init(void)

{

    DEV_Digital_Write(EPD_DC_PIN, 0);

    DEV_Digital_Write(EPD_CS_PIN, 0);

    DEV_Digital_Write(EPD_RST_PIN, 1);

}



void DEV_Module_Exit(void)

{

    DEV_Digital_Write(EPD_DC_PIN, 0);

    DEV_Digital_Write(EPD_CS_PIN, 0);



    //close 5V

    DEV_Digital_Write(EPD_RST_PIN, 0);

}

Code: Untitled.c Select all

#ifndef _DEV_CONFIG_H_

#define _DEV_CONFIG_H_



#pragma once

#include "freertos/FreeRTOS.h"

#include "freertos/task.h"

#include "driver/gpio.h"

#include <stdint.h>



#include "driver/spi_master.h"

/**

 * data

**/

#define UBYTE   uint8_t

#define UWORD   uint16_t

#define UDOUBLE uint32_t



/**

 * e-Paper GPIO

**/

#define EPD_RST_PIN     2

#define EPD_DC_PIN      12

#define EPD_CS_PIN      15

#define EPD_BUSY_PIN    4



/**

 * GPIO read and write

**/

#define DEV_Digital_Write(_pin, _value) gpio_set_level(_pin, _value == 0? 0:1)

#define DEV_Digital_Read(_pin) gpio_get_level(_pin)



/**

 * delay x ms

**/

//#define DEV_Delay_ms(__xms) vTaskDelay(__xms/ portTICK_RATE_MS)

#define DEV_Delay_ms(__xms) vTaskDelay(__xms/ portTICK_RATE_MS)



void DEV_SPI_WriteByte(UBYTE value);



void DEV_Module_Init(void);

void DEV_Module_Exit(void);

#endif