ESP32-C3-DevKitC-02开发板蓝牙广播问题

[Zhangquan]

我购买了一块ESP32-C3-DevKitC-02的开发版，想通过AT指令控制蓝牙功能。
顺序执行如下的指令
AT+BLEINIT=2
AT+BLEADVPARAM=160,160,0,0,7
AT+BLEADVDATAEX="ESP-AT","A002","0102030405",1
AT+BLEADVSTART
执行每一条指令都返回OK，但执行完成后，我在手机上并不能看到此蓝牙的广播信息，请问可能是什么与原因

附相关信息
1. 启动串口信息
ESP-ROM:esp32c3-api1-20210207
Build:Feb 7 2021
rst:0x3 (RTC_SW_SYS_RST),boot:0xc (SPI_FAST_FLASH_BOOT)
Saved PC:0x403806a8
SPIWP:0xee
mode:DIO, clock div:2
load:0x3fcd5820,len:0x16a8
load:0x403cc710,len:0x93c
load:0x403ce710,len:0x2eb8
entry 0x403cc710
[0;32mI (35) boot: ESP-IDF v5.0.6-dirty 2nd stage bootloader[0m
[0;32mI (35) boot: compile time 08:51:32[0m
[0;32mI (35) boot: chip revision: v0.4[0m
[0;32mI (37) boot.esp32c3: SPI Speed : 40MHz[0m
[0;32mI (42) boot.esp32c3: SPI Mode : DIO[0m
[0;32mI (47) boot.esp32c3: SPI Flash Size : 4MB[0m
[0;32mI (52) boot: Enabling RNG early entropy source...[0m
[0;32mI (57) boot: Partition Table:[0m
[0;32mI (61) boot: ## Label Usage Type ST Offset Length[0m
[0;32mI (68) boot: 0 otadata OTA data 01 00 0000d000 00002000[0m
[0;32mI (75) boot: 1 phy_init RF data 01 01 0000f000 00001000[0m
[0;32mI (83) boot: 2 nvs WiFi data 01 02 00010000 0000e000[0m
[0;32mI (90) boot: 3 at_customize unknown 40 00 0001e000 00042000[0m
[0;32mI (98) boot: 4 ota_0 OTA app 00 10 00060000 001d0000[0m
[0;32mI (105) boot: 5 ota_1 OTA app 00 11 00230000 001d0000[0m
[0;32mI (113) boot: End of partition table[0m
[0;32mI (117) esp_image: segment 0: paddr=00060020 vaddr=3c160020 size=31a40h (203328) map[0m
[0;32mI (168) esp_image: segment 1: paddr=00091a68 vaddr=3fc96200 size=0396ch ( 14700) load[0m
[0;32mI (172) esp_image: segment 2: paddr=000953dc vaddr=40380000 size=0ac3ch ( 44092) load[0m
[0;32mI (185) esp_image: segment 3: paddr=000a0020 vaddr=42000020 size=15e318h (1434392) map[0m
[0;32mI (485) esp_image: segment 4: paddr=001fe340 vaddr=4038ac3c size=0b458h ( 46168) load[0m
[0;32mI (497) esp_image: segment 5: paddr=002097a0 vaddr=50000000 size=00018h ( 24) load[0m
[0;32mI (504) boot: Loaded app from partition at offset 0x60000[0m
[0;32mI (504) boot: Disabling RNG early entropy source...[0m
no external 32k oscillator, disable it now.
at param mode: 1
AT cmd port:uart1 tx:7 rx:6 cts:5 rts:4 baudrate:115200
module_name: MINI-1
max tx power=78, ret=0
v3.3.0.0

2. AT信息
[15:32:10.106]收←◆
ready

[15:32:22.305]发→◇AT+BLEINIT=2
□
[15:32:22.305]收←◆AT+BLEINIT=2

[15:32:22.385]收←◆
OK

[15:32:27.540]发→◇AT+BLEADVPARAM=160,160,0,0,7
□
[15:32:27.556]收←◆AT+BLEADVPARAM=160,160,0,0,7

OK

[15:32:30.402]发→◇AT+BLEADVDATAEX="ESP-AT","A002","0102030405",1
□
[15:32:30.418]收←◆AT+BLEADVDATAEX="ESP-AT","A002","0102030405",1

OK

[15:32:36.780]发→◇AT+BLEADVSTART
□
[15:32:36.780]收←◆AT+BLEADVSTART

OK